![]() You can easily lose some of these screws if you do not keep them safe. The mop has numerous small screws that hold the different parts together. Keeping your screws safelyīefore you start taking your Shark steam mop apart, get a safe container to hold your screws. Ensure that you also have a metal spudger to remove other parts of the mop such as the steam control button. Screwdrivers of the right size correspond with the thickness of the blade and fit perfectly on the slot. You need to have the correct size of screwdrivers to unscrew the various screws of different sizes on the mop. However, you should further wring it with your hands to let out any remaining water and dry it completely. This mop head is self-wringing so all you need to do is twist it and it will let most of the water out. Water can spread to critical parts such as power slots ruining the entire power system. You should ensure that all parts of the mop are dry before taking it apart. The power can also ruin some parts of the mop, forcing you to buy replacement parts or an entire mop. Attempting to take it apart when still connected to the power can cause electrocution. Disconnecting The Mop From The Power Supplyīefore working on your Shark steam mop ensure that you disconnect it from the power source. The factors below ensure your safety and protect the mop from damage. 5 Things You Should Consider While Taking Apart Shark Steam Mopīefore taking your Shark steam mop apart you should take various factors into consideration. ![]() Separate the mop body from the tank by pulling it apart. Remove the screws and pull the black foam back to remove the third 12mm Phillips screws. Locate two 12mm Phillips screws on the top. Detach the mop body bottom from the grey connector. Unscrew the four 12mm Phillips screws inside the mop body. ![]() Unscrew the 12mm Phillips screws on the top left to expose the inside body. Pull the front and backside apart to open the plastic mop body. Locate four 16mm T1oTorx screws at the back of the mop, unscrew and remove it.ĭetach the power cord from the device by unscrewing the two 12mm Phillips head screws. Locate three 12mm Phillips screws and detach them from the plastic trim. Unscrew all the screws on the control panel to open the mop body. Remove the front plate to allow you to access the control panel. Unscrew the screws to remove the plastic cover. Locate two 12mm Phillips screws underneath. Locate the Shark logo decal located at the front of the body and remove it using a metal spudger. Unscrew the screws to detach the plastic trim from the body. Use a metal spudger to remove the steam control button from the upper surface of the body. Remove the 16mm screws to detach the water tank cap from the body. Locate the third screw on the opposite side at the bottom. Locate three T10 Torx screws located close to the top of the body. Removing the screws will require you to use a screwdriver. Unscrew the screws then pull out the plastic cap to detach it from the body. Locate the screws that connect the 12mm Phillips head to the body. Pull the handle out, separating it from the body. Remove the Phillips head above the cap of the water tank. Once you disconnect it, uncover the power cord from the mop handle. This step saves you from electric shocks that may cause harm or death. The first step to undertake when taking apart an electric device is to disconnect it from the power source. Step 1: Disassembling All Parts On The Front Panel Read on to learn how to take apart your shark steam mop step by step. You need to know how to dismantle your Shark steam mop to avoid damaging the parts. Here are some pics of the places on the steam mop where steam was coming out.At some point when using your shark steam mop you will need to dismantle it to clean or replace some parts. That's my two cents on products in my home that have leaked. It only lasted a month before it leaked water all over the place. Keep in mind, I don't drink coffee, but everybody else in my house does.Ī month ago, my dad received a "Breathe Easy" humidifier as a gift which was an "As Seen on TV" product. ![]() We just threw it away a couple weeks ago. We used to have a Ninja Coffee Bar, but it lasted only two years before an internal component stopped working, causing water to leak all over the place and onto the floor. I also wanted to add that some other small appliances in my house have also started leaking this year. I think it's safe to say that this steam mop is dead. Now the blue power light intermittently flashes and just turns off. But then, it stopped and steam came out of the body of the mop and the upper handle. Initially, I went outside and pumped the handle several times, and a lot of steam came out. I tried your suggestion by filling up the tank with pure white vinegar and running the mop to try and flush out the openings. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |